manualshive.com logo in svg

Siemens SiPass integrated, Controller And Device Installation Manual

Share
Download
Siemens SiPass integrated Controller And Device Installation Manual Download Page 16

 

 

Access Controllers 
AC5102 (ACC-G2) 

2 

16 | 38 

 

A6V11164550 

 

2.2.6

 

Recovering a Non-responsive Board 

See section 

Restoring/Updating Platform via SD Card [➙

 16] for details. 

2.2.7

 

ACC-G2 Firmware Update Procedures 

See section Common Firmware 

Update Procedure [➙

 11] for details. 

2.2.8

 

Restoring/Updating Platform via SD Card 

2.2.8.1

 

Preparing the SD Card 

Before you begin, prepare the SD Card by following the steps below: 
1.

 

Insert the SD card into the computer (512MB minimum - 2 GB maximum, 

512MB recommended for compatibility with older ACC revisions). 

2.

 

Find compressed 

.gz

 image in 

SD_Card

 folder. Unzip to extract the 

.wic

 file. 

3.

 

Use 

Win32DiskImager

 (in 

Tools\ACC-G2 SD-Card Creator Tool

 folder) to write 

the 

~.wic

 file to the SD Card. 

 

Win32DiskImager

 defaults to open a file of extension type 

*.img

, so select 

*.*

, 

browse to the location of the SD card image file and load it, then click the Write 

button. 

Note: Win32DiskImager must be installed on your computer, not on the SD card. 

 

 

Summary of Contents for SiPass integrated







































Reviews:

No comments

Brands by name

Popular brands

Load more brands