Siemens SINUMERIK MC Commissioning Manual Download | Manualshive

Page: 121 / 408

background image

configured gear stages. If the set braking time is too short, then alarm 22002 "Channel %1 block

%2 axis %3: braking time %6 [s] longer than the stop D time. Reason: %5" is output.
If the spindle is in axis operation, then it behaves just like an axis.

Adaptation of the dynamic response for coupling
For a coupling group, if all coupled axes and spindles can no longer be reliably and safely

stopped in synchronism within a transition time parameterized in p9553, a STOP D is

automatically triggered for all axes of the coupled group.
For a synchronous spindle coupling, the coupling is always kept when synchronous operation

is reached. The coupling group is always braked via the leading spindle. If the following spindle

requires a longer braking time than the leading spindle, p9553 must be increased accordingly

for the leading spindle.
When a synchronous spindle is active, STOP D should also be triggered for the leading and

following spindle.
Endlessly rotating axes are braked at the acceleration limit.
The SOS function is automatically activated after the transition time set in p9553 expires.

Alarms are triggered for:
The following formulas are applied when initiating the two alarms 22001/22002:

METRIC:

p9553 > MAX_AX_VELO * 1/60000 / MAX_AX_ACCEL

INCH/ROT/SPINDLE: p9553 > MAX_AX_VELO * 1/60 / MAX_AX_ACCEL

For axes with jerk limitation, the minimum braking time is increased by the additional

component:

2 * MAX_ACCEL / MAX_AX_JERK

The check is made for NEWCONF, RESET, unparking an axis and for programming ACC or

JERKLIM.
The MD names contained in the formulas must, corresponding to the alarm situation (the alarm

occurs when parameterizing or when programming), be replaced by other values when

required.

MD

Alternative MD

Gearbox stage-specific MD spindle

Program

command

MAX_AX_VE‐

LO

min(JOG_VELO, JOG_VE‐

LO_RAPID)

$MA_GEAR_STEP_MAX_VE‐

LO_LIMIT[0…max]
$MA_GEAR_STEP_PC_MAX_VE‐

LO_LIMIT[0…max]

-

MAX_AX_AC‐

CEL

MAX_AX_ACCEL

$MA_GEAR_STEP_SPEEDCTRL_

ACCEL[0…max]
$MA_GEAR_STEP_POSCTRL_AC‐

CEL[0…max]

ACC

MAX_AX_JER

K

JOG_AND_POS_MAX_JERK

JERKLIM

Safety functions integrated in the drive

4.6 SS2

Safety Integrated (with SINAMICS S120)

Commissioning Manual, 02/2020, A5E46305916B AB

121

«
...
119
120
121
122
123
...
»

Summary of Contents for SINUMERIK MC

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK MC

Brand: Galcon Pages: 32

Ascotel Office 45

Brand: Aastra Pages: 40

Brand: Aastra Pages: 244

Brand: Aastra Pages: 30

Brand: Aastra Pages: 24

IntelliGate A150

Brand: Aastra Pages: 524

Ascotel IntelliGate 150

Brand: Aastra Pages: 228

Brand: Daikin Pages: 5

Brand: tams elektronik Pages: 60

Brand: Hach Pages: 2

Brand: Hach Pages: 12

Brand: Hach Pages: 472

Brand: Hach Pages: 64

Brand: V2 ELETTRONICA Pages: 6

Brand: Hach Pages: 210

Brand: GBD Pages: 15

Brand: Jacka Industries Pages: 24

Digiplex DGP-848

Brand: Paradox Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands