Siemens SINAMICS Startdrive Getting Started Download Page 73

Page: 73 / 102

Safety Integrated

9.5 Commissioning extended functions

Getting Started - SINAMICS Startdrive
Getting Started, 01/2015

9.4.5

Completing the safety commissioning

Safety commissioning completion

To complete the commissioning, the safety parameterization must be copied to the ROM of

the drive and into the project.
1.

Click the

button to exit the safety commissioning mode.

Click "Yes" to confirm the opened dialog. The drive parameters are copied from RAM to

ROM.

Figure

9-8

Safety commissioning: Copy RAM to ROM

Close the online connection to the drive device.

Click the "Load from device (software)" button in the toolbar to save the safety

parameterization in the Startdrive project.

Switch the drive device Off and On so that the safety commissioning in the drive device

acts.

This completes the safety commissioning.

9.5

Commissioning extended functions

9.5.1

Commissioning Safety Integrated extended functions

Extended functions

Summary of Contents for SINAMICS Startdrive







































































































Search results

Summary of Contents for SINAMICS Startdrive

Reviews:

Related manuals for SINAMICS Startdrive

Brands by name

Popular brands

Siemens SINAMICS Startdrive, Getting Started

Search results

Summary of Contents for SINAMICS Startdrive

Reviews:

Related manuals for SINAMICS Startdrive

Brands by name

Popular brands