Siemens SIMOTICS M-1PH818 Page 56 Operating And Installation Instructions Download | Manualshive

Page: 56 / 314

background image

Note
Type of balancing
In the case of shaft extensions with feather keys, the type of balancing is also included on the

rating plate next to the CE mark.

5.2.5

Lifting and transporting the machine

To safely lift and transport the machine, the following requirements must be met:
● Personnel operating cranes and fork-lift trucks must be appropriately qualified.
● If the motor is packed, depending on the weight, size and on-site conditions, lift crates and

transport frames using a fork-lift truck or a crane with slings. Use a crane or fork-lift truck

suitable for the load.

● When lifting the machine, use only approved and undamaged sling guides and spreaders

of sufficient rated capacity. Check the lifting equipment prior to its use. The weight of the

machine is shown on the rating plate.

● When lifting the machine, refer to the information on the lifting plate.

– Comply with the specified spreading angles.
– Do not exceed the maximum lifting acceleration and lifting speed specified on the lifting

plate. Lift the machine without jerking it.

Acceleration a ≤ 0.4 g (≈ 4 m/s

2

)

Velocity v ≤ 20 m/min

● Use only the load carrying device on the stator frame for lifting.

WARNING

Transport for a different type of construction
If you do not transport or lift the machine in a position appropriate for its construction, the

machine can tip, slip into the lifting equipment or fall down. This can result in death, serious

injury or material damage.
● Use only the load carrying device on the stator frame for lifting.
● Use the load carrying device appropriate for the machine position.
● Use suitable rope guiding or spreading devices. The weight of the machine is shown on

the rating plate.

Mounting
5.2 Lift the machine to where it will be mounted and position it

SIMOTICS M-1PH8 1PH818., 1PH822., 1PH828.

56

Operating Instructions 10/2017

«
...
54
55
56
57
58
...
»

Summary of Contents for SIMOTICS M-1PH818



























































































































































































































































































































Reviews:

No comments

Related manuals for SIMOTICS M-1PH818

Raptor JET SERIES

Brand: Indmar Pages: 82

Brand: EBARA Pages: 36

Brand: Hatz Diesel Pages: 48

Brand: RenewAire Pages: 28

Brand: dunkermotoren Pages: 32

PNEUTORQUE PT 1

Brand: norbar Pages: 11

Brand: Geely Pages: 198

Brand: Teryair Pages: 13

Brand: Vacmaster Pages: 12

Brand: Superrollo Pages: 68

Brand: Oriental motor Pages: 8

Brand: Oriental motor Pages: 12

Brand: Wilesco Pages: 4

Brand: YS Pages: 2

Brand: Yanmar Pages: 308

Brand: Nanomotion Pages: 42

Brand: Vanguard Pages: 136

max-18tz series

Brand: O.S. engine Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands