Siemens SIMOTICS M-1PH818 Page 41 Operating And Installation Instructions Download | Manualshive

Page: 41 / 314

background image

4.13.5

Transporting the machine set

WARNING

Falling down of the machine
The lifting lugs on the machine are designed only for the weight of the machine. If a machine

set is lifted and transported on a single machine, this can lead to mechanical failure of the

lifting lug. The machine or machine set may fall. This can result in death, serious injury or

material damage.
● Do not lift machine sets by attaching lifting tackle to the individual machines.
● Use only the equipment provided, e.g. the openings or lugs on the base plates, for

transporting machine sets. Note the maximum capacity of the lifting lug.

Note
Place the machine in a secure and raised position
In order to obtain easy and safe access to the underside of the machine, place it in a secure

and raised position.

DANGER

Standing under suspended loads
If the lifting gear or load handling attachments were to fail, the machine could fall. This can

result in death, serious injury or material damage.
Never remain under or in the immediate vicinity of the machine when it is raised.

4.13.6

Storage

You can store the machine for up to two years in dry, dust-free and vibration-free rooms without

reducing the specified storage time.

NOTICE
Seizure damage to bearings
If the motor is stored incorrectly, bearing damage can occur at standstill, e.g. brinelling, as a

result of vibration or shock.
Read the following storage instructions.

Preparation

● Fit the rotor shipping brace.
● Apply a preserving agent, for example to external components such as shaft ends, if this

has not already been applied in the factory.

Preparations for use

4.13 Transport and storage

SIMOTICS M-1PH8 1PH818., 1PH822., 1PH828.

Operating Instructions 10/2017

41

«
...
39
40
41
42
43
...
»

Summary of Contents for SIMOTICS M-1PH818



























































































































































































































































































































Reviews:

No comments

Related manuals for SIMOTICS M-1PH818

Brand: Valor Pages: 97

Brand: Vanguard Pages: 20

Command Pro CH940-CH1000

Brand: Kohler Pages: 16

Brand: BONFIGLIOLI Pages: 16

Brand: Danfoss Pages: 32

Brand: Polini Pages: 32

44 A FOUR-35C THREE

Brand: Westerbeke Pages: 61

Brand: KONTRONIK Pages: 6

Brand: Bodine Pages: 8

Brand: AUSTAR Pages: 11

Brand: Viessmann Pages: 14

Brand: Volvo Penta Pages: 8

Brand: Volvo Penta Pages: 20

Brand: Elite Pages: 2

Brand: Volvo Pages: 25

Brand: Sisu Diesel Pages: 116

Brand: Yanmar Pages: 214

Brand: Ingersoll-Rand Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands