Siemens SIMOTICS M-1PH818, Operating And Installation Instructions

Page: 255 / 314

Operating instructions
K3G250-RR03-M4
Siemens AG PD LD Nbg.
Translation of the original operating instructions
3.2 Nominal data
Motor M3G084-DF
Phase 3~
Nominal voltage / VAC
400
Nominal voltage
range / VAC 380 .. 480
Frequency / Hz 50/60
Method of obtaining
data ml
Speed (rpm) / min -1 2900
Power consumption / W 240
Current draw / A 0.44
Min. ambient
temperature / °C -25
Max. ambient
temperature / °C 60
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
Actual Req. 2015
01 Overall efficiency η
es
/ %
46.9 43.9
02 Measurement category A
03 Efficiency category Static
04 Efficiency grade N 64.1 61
05 Variable speed drive Yes
06 Year of manufacture The year of manufacture is specified on the
product's rating label.
07 Manufacturer ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart
· HRA 590344
D-74673 Mulfingen
08 Type K3G250-RR03-M4
09 Power consumption P
ed
/ kW 0.23
09 Air flow q
v
/ m³/h 700
09 Pressure increase total p
sf
/
Pa
500
10 Speed (rpm) n / min -1 2920
11 Specific ratio * 1.01
12 Recycling/disposal Information on recycling and disposal is
provided in the operating instructions.
13 Maintenance Information on installation, operation and
maintenance is provided in the operating
instructions.
14 Additional components Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
* Specific ratio = 1 + p
fs
/ 100 000 Pa
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
3.4 Technical description
Weight 11.8 kg
Fan size 250 mm
Rotor surface Painted black
Electronics housing
material Die-cast aluminum, painted black
Impeller material PA plastic, galvanized sheet-metal plate
Housing material
Die-cast aluminum
Support plate material Sheet steel, galvanized
Inlet nozzle material Sheet steel, galvanized
Guard grille material Steel, phosphated and coated with black
plastic (RAL 9005)
Number of blades 7
Direction of rotation Clockwise, viewed toward rotor
Degree of protection IP55
Insulation class "F"
Moisture (F) /
Environmental (H)
protection class H1
Installation position
Any
Condensation
drainage holes None
Mode S1
Motor bearing Ball bearing
Technical features - Output 10 VDC, max. 10 mA
- Operation and alarm display
- External 24 V input (parameter setting)
- Alarm relay
- Integrated PID controller
- Motor current limitation
- PFC, passive
- RS-485 MODBUS-RTU
- Soft start
- EEPROM write cycles: 100,000
maximum
- Control input 0-10 VDC / PWM
- Control interface with SELV potential
safely disconnected from the mains
- Thermal overload protection for
electronics/motor
- Line undervoltage / phase failure
detection
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
<= 3.5 mA
Electrical hookup Via terminal box
Motor protection Thermal overload protector (TOP)
internally connected
Protection class I (if protective earth is connected by
customer to the housing's connection point)
Conformity with
standards EN 61800-5-1; CE
Approval C22.2 No.77 + CAN/CSA-E60730-1;
EAC; UL 1004-7 + 60730
Item no. 55691-5-9970 · ENU · Change 94618 · Approved 2017-06-12 · Page 5 / 12
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
255