Siemens SIMOTICS M-1PH818 Page 46 Operating And Installation Instructions Download

Page: 46 / 314

Measures to reduce bearing currents

To specifically reduce and prevent damage caused by bearing currents, consider the system

as a whole, which comprises the motor, converter, and driven machine. The following

precautions help to prevent bearing currents:
● Setting up a properly meshed grounding system in the system as a whole, with low

impedance for high-frequency currents

● No potential difference between the motor, converter, and working machine.

– Use symmetrical, shielded connecting cables.
– Connect the cable shield at both ends over the greatest possible surface area (360°

contact).

– Use equipotential bonding conductors between the motor and the driven machine as

well as between the motor and the converter

● Limit the voltage rate of rise by using an output filter to dampen harmonic components in

the output voltage

4.14.2

Insulated bearings for converter operation

If the machine is operated with a low-voltage converter such as SINAMICS G150 / S150 /

S120, then an insulated bearing and a speed encoder with insulated bearings (option) is

mounted at the non-drive end.
For 1PH818, the insulated bearings are optional; for 1PH822 and 1PH828, insulated bearings

are standard.
Comply with the plates on the machine relating to bearing insulation and possible bridges.

①

Driven machine

④

Insulated bearings

②

Motor

⑤

Insulated tachometer fitting

③

Coupling

Figure 4-6

Schematic representation of a single drive

Preparations for use
4.14 Converter operation

SIMOTICS M-1PH8 1PH818., 1PH822., 1PH828.

Operating Instructions 10/2017

Summary of Contents for SIMOTICS M-1PH818



























































































































































































































































































































Search results

Summary of Contents for SIMOTICS M-1PH818

Reviews:

Related manuals for SIMOTICS M-1PH818

Brands by name

Popular brands

Siemens SIMOTICS M-1PH818, Operating And Installation Instructions

Search results

Summary of Contents for SIMOTICS M-1PH818

Reviews:

Related manuals for SIMOTICS M-1PH818

Brands by name

Popular brands