Siemens SIMATIC S5 Series, Manual

Page: 67 / 109

ASCII Driver S5-95U, Second Serial Interface
4.4 Parameterizing the ASCII Driver in DB1
In order to simplify parameterizing, the DB1 with default parameters is already integrated in the PLC.
If you load the default DB1 from the PLC into the programmer after an
”
overall reset
”
and display it
on the screen, it has the following structure:
Figure 4-7 DB1 with Default Parameters
0: KS ='DB1 OBA: AI 0 ; OBI: ';
12: KS =' ; OBC: CAP N CBP ';
24: KS ='N ;#SL1: SLN 1 SF ';
36: KS ='DB2 DW0 EF DB3 DW0 ';
48: KS =' KBE MB100 KBS MB1';
60: KS ='01 PGN 1 ;# SDP: N';
72: KS ='T 128 PBUS N ; TFB: OB13';
84: KS =' 100 ; #CLP: STW MW10';
96: KS ='2 CLK DB5 DW0 ';
108: KS =' SET 3 01.10.91 12:00:';
120: KS ='00 OHS 000000:00:00 ';
132: KS =' TIS 3 01.10. 12:00:00 ';
144: KS =' STP Y SAV Y CF 00 ';
156: KS =' ; # #RKT: PAR DB202DW0 ';
168: KS =' SF DB203DW0 EF DB204';
180: KS ='DW0 KBS MB104 KBE';
192: KS =' MB105 MOD 1 BDR ';
204: KS ='9600 PRTY EVEN DF 1 DT ';
216: KS ='220 PRI HIGH TIO 2000';
228: KS =' BWT 4000 TTE 6 ';
240: KS ='TTS 6 ;# #ASC: PAR ';
252: KS ='DB202DW0 SF DB203DW0 ';
264: KS =' EF DB204DW0 KBS MB104';
276: KS =' KBE MB105 MOD';
288: KS =' 1 BDR 9600 PRTY EVEN ';
300: KS ='DF 0 DT 100 ML 64 ;';
312: KS =' # END ';
a a a a a
a a a a a
a a a a a
a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a
Default parameter for ASCII driver
The parameters of the ASCII driver are assigned with the
”
ASC:
”
blocking designation in the
parameter block (in Figure 4-7, grey shaded).
The ASCII parameter block is enclosed between comment characters (#) and is not interpreted by
the PLC in this form. For this reason, overwrite with a blank the comment character preceding the
”
ASC:
”
block designation and following the last ASCII parameter.
Caution: The parameter block for the computer link (RKT:) must remain enclosed between
comment characters! Only one communication possibility can be parameterized for the second serial
interface.
The procedure for the entering, changing and transmitting of the DB1 is explained in detail in the
S5-90U/S5-95U System Manual, Section 9.1.3.
The following table ( Table 4.2) shows all parameters for the ASCII driver with their value ranges.
The parameters are then explained.
4-8
EWA 4NEB 812 6095-02