Siemens SIMATIC RTLS System Manual Download Page 74

Page: 74 / 204

6.1.2

Installation & Operation

6.1.2.1

Notes on installation

Before you install the devices, read this section carefully to ensure trouble-free installation and

operation.
The devices can only be used in conjunction with the RTLS localization system. Setup,

installation and use of the tools and clients of the RTLS localization system are described in the

corresponding manuals.
The device is intended for fixed installation on walls or ceilings. Installation is to be performed

by qualified and trained personnel according to the operating instructions. In addition,

installation must take place in accordance with the respective instructions for the installation of

electrical systems and utilities. The devices must be installed so that they are accessible for

future maintenance, e.g., for opening the enclosure cover.
Note the specifications in the section "Technical specifications" during installation and

operation. Ensure that all screws are securely and firmly screwed into the wall / ceiling and can

support the weight of the device and its wiring.
Make sure that the ambient temperature does not exceed 50 °C and that the device is not

installed at a location where it is exposed to direct sunlight.

Connection of the cables

Make sure that the Twist-Lock connectors are inserted correctly to prevent moisture from

entering the enclosure.
Make sure that the wiring is correct before you start up the device.
Only use the cables described in the manual, supplied with the device or otherwise prescribed.

SIEMENS AG is not liable for damages or functional limitations caused by the use of other

cables.
Protect the device from penetrating moisture by closing off connectors that are not in use with

suitable covers. These covers are installed on the device.

Supply voltage

When the supply voltage is connected to the power plug, all LEDs flash briefly for a moment.

The POWER LED lights up as soon as voltage is present.
The device can be supplied with power via the Ethernet cable. In this case, the power plug

should be tightly sealed to prevent moisture from penetrating. Do not supply the device with

power through the mains and the PoE connection at the same time.

Gateways
6.1 SIMATIC RTLS4030G

System Manual, 04/2019, C79000-G8976-C577-01

Summary of Contents for SIMATIC RTLS













































































































































































































Search results

Summary of Contents for SIMATIC RTLS

Reviews:

Brands by name

Popular brands

Siemens SIMATIC RTLS, System Manual

Search results

Summary of Contents for SIMATIC RTLS

Reviews:

Brands by name

Popular brands