Siemens SIMATIC RTLS System Manual Download Page 43

FCC information

Siemens SIMATIC RTLS4330A (MLFB 6GT2701-5EA03); FCC ID NXW-RF380R02
This device complies with part 15 of the FCC rules. Operation is subject to the following two 

conditions: 
(1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that may cause 

undesired operation. 

Caution
Any changes or modifications not expressly approved by the party responsible for compliance 

could void the user's authority to operate the equipment.

Note 
This equipment has been tested and found to comply with the limits for a Class A digital device, 

pursuant to part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference when 

the equipment is operated in a commercial environment. This equipment generates, uses, and 

can radiate radio frequency energy and, if not installed and used in accordance with the 

instruction manual, may cause harmful interference to radio communications. Operation of this 

equipment in a residential area is likely to cause harmful interference in which case the user will 

be required to correct the interference at his own expense. 

IC information

This device complies with Industry Canada license-exempt RSS standard(s). Operation is 

subject to the following two conditions: 
(1) This device may not cause interference, and 
(2) this device must accept any interference, including interference that may cause undesired 

operation of the device. 
Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio 

exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : 
(1) L`appareil ne doit pas produire de brouillage, et 
(2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le 

brouillage est susceptible d`en compromettre le fonctionnement. 

Anchors

5.2 SIMATIC RTLS4330A

System Manual, 04/2019, C79000-G8976-C577-01

43

Summary of Contents for SIMATIC RTLS













































































































































































































Reviews: