Siemens SIMATIC RTLS System Manual Download Page 194

Page: 194 / 204

● ETSI EN 301 489-33

Electromagnetic compatibility and radio spectrum matters (ERM) - Electromagnetic

compatibility for radio equipment and services - Part 33:

Special conditions for ultra-wideband (UWB) devices

● EN 55011

Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics –

Limits and methods of measurement

● EN 55032 Class A, Class B

Electromagnetic compatibility of multimedia equipment – Emission requirements

● EN 55035

Electromagnetic compatibility of multimedia equipment - Immunity requirements

● EN 61000-6-1

Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for

residential, commercial and light-industrial environments

● EN 61000-6-2

Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial

environments

● EN 61000-6-3

Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for

residential, commercial and light-industrial environments

● EN 61000-6-4

Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for

industrial environments

Article 3 (2) Efficient use of the radio spectrum

● ETSI EN 300 328

Wideband transmission systems; Data transmission equipment operating in the 2.4 GHz

ISM band and using wide band modulation techniques. Harmonized standard covering the

essential requirements of article 3.2 of the EU Directive 2014/53/EU

● ETSI EN 302 065-2

Short Range Devices (SRD) using ultra-wideband technology (UWB); Harmonized

standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part

2: Requirements for UWB location tracking

Note
The specified approvals are only valid if the corresponding symbol is printed on the device.

FCC information

Siemens SIMATIC RTLS PCB OEM PULSE (MLFB 6GT2700-8AF03); FCC ID NXW-

RF380R02
This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions:
(1) This device may not cause harmful interference, and

Transponder
7.9 SIMATIC RTLS PCB OEM PULSE

194

System Manual, 04/2019, C79000-G8976-C577-01

Summary of Contents for SIMATIC RTLS













































































































































































































Search results

Summary of Contents for SIMATIC RTLS

Reviews:

Brands by name

Popular brands

Siemens SIMATIC RTLS, System Manual

Search results

Summary of Contents for SIMATIC RTLS

Reviews:

Brands by name

Popular brands