Siemens simatic PCIL43 Operating Instructions Manual Download

Page: 41 / 112

Commissioning

7.3 Notes on operation

SIMATIC Rack PC IL 43
Operating Instructions, Edition 09/2005, A5E00432875-01

7-9

Please replace the faulty drive with a new one of the same type and capacity.

Notice
You can exchange the drive without switching the device off (hot swap) on devices with

removable frames.

For devices without removable frames, drives may only be exchanged in switched off state.
The new drive can be configured into the RAID association at operating system level by

means of the RAID software. This is not possible as BIOS level.

Associate new hard drive

The command "Rescan for Plug and Play Devices" searches for and displays new drives.

Summary of Contents for simatic PCIL43

















































































































Search results

Summary of Contents for simatic PCIL43

Reviews:

Related manuals for simatic PCIL43

Brands by name

Popular brands

Siemens simatic PCIL43, Operating Instructions Manual

Search results

Summary of Contents for simatic PCIL43

Reviews:

Related manuals for simatic PCIL43

Brands by name

Popular brands