Siemens simatic PCIL43 Operating Instructions Manual Download

Page: 57 / 112

Maintenance and service

11.1 Removing and installing hardware components

SIMATIC Rack PC IL 43
Operating Instructions, Edition 09/2005, A5E00432875-01

11-3

11.1.3

Removing the power supply module

Warning
Only qualified personnel is authorized to exchange the power supply module.

Preparation

1. Unplug the device from mains and disconnect all cables.
2. Open the device.

Removing the power supply module

How to remove the power supply module
1. Disconnect the power cables from

the disk drives and motherboard.

2. Remove the tie-wraps holding the

power cables in the housing.

3. Remove the mounting screws

(TORX T10) (1).

4. Lift the power supply module out of

the enclosure until you can access

the power cable of the floppy disk

drive.

5. Disconnect this power cable from

the floppy disk drive.

6. Remove the screws (2) on the

steel bracket.

Summary of Contents for simatic PCIL43

















































































































Search results

Summary of Contents for simatic PCIL43

Reviews:

Related manuals for simatic PCIL43

Brands by name

Popular brands

Siemens simatic PCIL43, Operating Instructions Manual

Search results

Summary of Contents for simatic PCIL43

Reviews:

Related manuals for simatic PCIL43

Brands by name

Popular brands