Siemens simatic PCIL43 Operating Instructions Manual Download

Page: 56 / 112

Maintenance and service

11.1 Removing and installing hardware components

SIMATIC Rack PC IL 43

11-2

Operating Instructions, Edition 09/2005, A5E00432875-01

11.1.2

Replacing the backup battery

To be noted before you replace the battery

Caution
Risk of damage!
The lithium battery may only be replaced with an identical battery or with a type

recommended by the manufacturer.

Disposal

Caution
Depleted batteries must be disposed of in accordance with with local regulations.

Preparation

Note
The configuration data of the device are deleted when the battery is replaced. Note the

current BIOS Setup settings. You can conveniently back up the BIOS settings by means of

the SIMATIC PC BIOS manager.

Replacing the battery

The location of the backup battery on the motherboard and the procedure for replacing it is

described in technical manual, D2156-S.pdf, on the supplied "Documentation and Drivers"

CD.

Reconfiguring the BIOS Setup

When a battery is exchanged, the configuration data of the device is lost and must be

reentered in the BIOS setup.

Summary of Contents for simatic PCIL43

















































































































Search results

Summary of Contents for simatic PCIL43

Reviews:

Related manuals for simatic PCIL43

Brands by name

Popular brands

Siemens simatic PCIL43, Operating Instructions Manual

Search results

Summary of Contents for simatic PCIL43

Reviews:

Related manuals for simatic PCIL43

Brands by name

Popular brands