Siemens simatic PCIL43 Operating Instructions Manual Download

Page: 11 / 112

SIMATIC Rack PC IL 43
Operating Instructions, Edition 09/2005, A5E00432875-01

2-1

Safety information

2.1

General safety instructions

Caution
Please observe the safety instructions on the back cover of this documentation. You should

not expand your device unless you have read the relevant safety instructions.

This device is compliant with the relevant safety measures to IEC, EN, VDE, UL, and CSA. If

you have questions about the validity of the installation in the planned environment, please

contact your service representative.

Repairs

Only authorized personnel are permitted to repair the device.

Warning
Unauthorized opening of and improper repairs to the device may result in substantial

damage to equipment or endanger the user.

System expansions

Only install system expansion devices designed for this device. If you install other expansion

devices, you may damage the system or violate the safety requirements and regulations on

RF suppression. Contact your technical support team or where you purchased your PC to

find out which system expansion devices may safely be installed.

Caution
If you install or exchange system expansions and damage your device, the warranty

becomes void.

Summary of Contents for simatic PCIL43

















































































































Search results

Summary of Contents for simatic PCIL43

Reviews:

Related manuals for simatic PCIL43

Brands by name

Popular brands

Siemens simatic PCIL43, Operating Instructions Manual

Search results

Summary of Contents for simatic PCIL43

Reviews:

Related manuals for simatic PCIL43

Brands by name

Popular brands