Siemens SIMATIC NET S7-1200 Operating Instructions Manual Download Page 69

Page: 69 / 98

Configuration

5.4 Configuring the telecontrol instructions

CP 1242-7
Operating Instructions, 09/2011, C79000-G8976-C247-02

Parameter

Data type

Initial value

Description

GPRSmode

UINT

Mode of the CP:



0 = Telecontrol



1 = GPRS direct

TemporaryStation

BOOL

Bit 0: Temporary connection
If this option is selected, the CP only establishes a

temporary connection to send data. Once the frames

have been transferred, the CP terminates the connection

again.



1: activated (temporary connection)



0: deactivated (permanent connection)

SMS_Enabled

BOOL

Bit 1: Allow SMS
Selecting the option allows the S7 station to send SMS

messages.



1: activated (SMS allowed)



0: deactivated (no SMS)

Field for the "SMSC" parameter

In STEP 7, the corresponding data is located in the parameter area "Modem settings".

Table 5- 11 IF_CONF_SMS_Provider

Parameter

Data type

Initial value

Description

UINT

ID of the parameter field

Length

UINT

Length of the parameter field in bytes: 28

Mode

UINT

Validity (1: permanent, 2: temporary)

SMSProvider

STRING [20]

Node number of the SMS center (SMSC) of the GSM

network provider with which the contract was signed for

this station.

Field for the "PIN" parameter

In STEP 7, the corresponding data is located in the parameter area "Modem settings".

Table 5- 12 IF_CONF_PIN

Parameter

Data type

Initial value

Description

UINT

ID of the parameter field

Length

UINT

Length of the parameter field in bytes: 16

Mode

UINT

Validity (1: permanent, 2: temporary)

STRING [8]

PIN of the SIM card inserted in the SIM card
The parameter is not relevant if the PIN was correctly

configured. If the PIN was incorrectly configured, the

correct PIN can be entered.

Summary of Contents for SIMATIC NET S7-1200



































































































Search results

Summary of Contents for SIMATIC NET S7-1200

Reviews:

Related manuals for SIMATIC NET S7-1200

Brands by name

Popular brands

Siemens SIMATIC NET S7-1200, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET S7-1200

Reviews:

Related manuals for SIMATIC NET S7-1200

Brands by name

Popular brands