Siemens SIMATIC NET S7-1200 Operating Instructions Manual Download Page 17

Page: 17 / 98

Application and properties

1.7 Configuration examples

CP 1242-7
Operating Instructions, 09/2011, C79000-G8976-C247-02

TeleService via GPRS

In TeleService via GPRS, an engineering station on which STEP 7 is installed communicates

via the GSM network and the Internet with the CP 1242-7 in the S7-1200.
Since a firewall is normally closed for connection requests from the outside, a switching

station between the remote station and the engineering station is required. This switching

station can be a telecontrol server or, if there is no telecontrol server in the configuration, a

TeleService gateway.
●

Configuration with telecontrol server:
The connection runs via the telecontrol server.
–

The engineering station and telecontrol server are connected via the Intranet (LAN) or

Internet.

–

The telecontrol server and remote station are connected via the Internet and via the

GSM network.

The engineering station and telecontrol server can also be the same computer; in other

words, STEP 7 and TCSB are installed on the same computer.

6WDWLRQ

6ಣZLWK

&3ಣ

(QJLQHHULQJVWDWLRQ
ZLWK67(3

'6/URXWHU

,QWHUQHW

7HOHFRQWUROVHUYHUZLWKDSSOLFDWLRQ
7(/(&21752/6(59(5%$6,&

*356

,QGXVWULDO(WKHUQHW

Figure 1-4

TeleService via GPRS in a configuration with telecontrol server

Summary of Contents for SIMATIC NET S7-1200



































































































Search results

Summary of Contents for SIMATIC NET S7-1200

Reviews:

Related manuals for SIMATIC NET S7-1200

Brands by name

Popular brands

Siemens SIMATIC NET S7-1200, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET S7-1200

Reviews:

Related manuals for SIMATIC NET S7-1200

Brands by name

Popular brands