Siemens SIMATIC NET S7-1200 Operating Instructions Manual Download Page 36

Page: 36 / 98

Notes on operation

4.3 Main and substitute telecontrol server

CP 1242-7

Operating Instructions, 09/2011, C79000-G8976-C247-02

●

For telecontrol connections:
–

Text for the wake-up SMS message for establishing a connection to the telecontrol

server:

TELECONTROL

–

Text for the wake-up SMS message for establishing a connection to the main

telecontrol server:

TELECONTROL MAIN

–

Text for the wake-up SMS message for establishing a connection to the substitute

telecontrol server:

TELECONTROL BACKUP

The configuration of the telecontrol server for the CP 1242-7 is set in STEP 7 in

"Telecontrol interface > Operating mode > main or substitute telecontrol server".

Note
Wake-up with a mobile phone



One of the texts listed above can be used in a wake-up SMS message.



With a wake-up call, the station always connects to the main telecontrol server.

●

For TeleService connections:
–

Text for the wake-up SMS message for establishing a connection to the first

configured TeleService server:

TELESERVICE

TELESERVICE 1

–

Text for the wake-up SMS message for establishing a connection to the second

configured TeleService server:

TELESERVICE 2

For TeleService, no extra wake-up SMS needs to be sent since the connection

establishment is initiated by the engineering station.
The configuration of the TeleService server for the CP 1242-7 is set in STEP 7 in

"Telecontrol interface > TeleService settings.

4.3

Main and substitute telecontrol server

Telecontrol server: Main and substitute server

If TCSB is installed as the main and substitute server, two parallel systems are installed by

TCSB and these are independent of each other. Both systems have their own database and

the complete communications functions of TCSB. The two TCSB systems do not monitor

each other.

Summary of Contents for SIMATIC NET S7-1200



































































































Search results

Summary of Contents for SIMATIC NET S7-1200

Reviews:

Related manuals for SIMATIC NET S7-1200

Brands by name

Popular brands

Siemens SIMATIC NET S7-1200, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET S7-1200

Reviews:

Related manuals for SIMATIC NET S7-1200

Brands by name

Popular brands