Siemens SIMATIC NET S7-1200 Operating Instructions Manual Download Page 41

Page: 41 / 98

Notes on operation

4.7 Diagnostics

CP 1242-7
Operating Instructions, 09/2011, C79000-G8976-C247-02

NOTICE

Canceling a TeleService connection when calling online dialogs
An existing TeleService connection is canceled when you attempt to access an additional

station or a node.
When there is an existing TeleService connection, do not select any of the menu

commands "Go online", "Online & Diagnostics", "Load to device", "Extended download to

device" or "Accessible nodes".

4.7

Diagnostics

Diagnostics options

You have the following diagnostics options available for the module:
●

The LEDs of the module
For information on the LED displays, refer to the section LEDs (Page 20).

●

STEP 7: The "Diagnostics" tab in the Inspector window
Here, you can obtain the following information on the selected module:
–

Entries in the diagnostics buffer of the CPU

–

Information on the online status of the module

●

STEP 7: Diagnostics functions in the "Online > Online and diagnostics" menu
Here, you can obtain static information on the selected module:
–

General information on the module

–

Diagnostics status

–

Information about the telecontrol interface:

- Network

- Ethernet interface

- Statistics

You can obtain further information on the diagnostics functions of STEP 7 in the STEP 7

online help.

4.8

Downloading firmware

New firmware versions

If a new firmware version is available for the module, you will find this on the Ethernet pages

of the Siemens Automation Customer Support under the following ID:

Summary of Contents for SIMATIC NET S7-1200



































































































Search results

Summary of Contents for SIMATIC NET S7-1200

Reviews:

Related manuals for SIMATIC NET S7-1200

Brands by name

Popular brands

Siemens SIMATIC NET S7-1200, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET S7-1200

Reviews:

Related manuals for SIMATIC NET S7-1200

Brands by name

Popular brands