background image

 

Technical specifications 

 

7.8 Hardware descriptions 

SIMATIC IPC520A 
Operating Instructions, 11/2021, A5E51366325-AA 

65

 

7.8.3.2

 

Micro SD interface 

Name of interface on the device:

 X50

 

 

Pin 

Abbreviation 

Function 

Dat2 

Data line bit 2 

Dat3 

Card Detect / data line bit 3 

CMD 

Command Line 

Vdd 

Voltage supply 2.7–3.6 V 

Clk 

Clock input 

GND 

Signal Ground 

Dat0 

Data line bit 0 

Dat1 

Data line bit 1 

7.8.3.3

 

M.2 interface 

M.2 Key E module  

Name of interface on the device: X100 

 

Pin no.

 

Signal

 

Signal

 

Pin no.

 

 

 

NC 

75 

 74 

3.3V 

GND 

73 

72 

3.3V 

GND 

71 

70 

3.3V 

NC 

69 

68 

SUSCLK 

RESET# 

67 

66 

SIM DETECT 

ANTCTL3 

65 

64 

COEX_RXD(I) 

ANTCTL2 

63 

62 

COEX_TXD(O) 

ANTCTL1 

61 

60 

COEX3(I/O) 

ANTCTL0 

59 

58 

NC 

GND 

57 

56 

NC 

REFCLKp 

55 

54 

PEWAKE# 

REFCLKn 

53 

52 

CLKREQ# 

GND 

51 

50 

PERST# 

PETp0 

49 

48 

NC 

PETn0 

47 

46 

NC 

GND 

45 

44 

ALERT# 

PERp0 

43 

42 

SMB_DATA 

PERn0 

41 

40 

SMB_CLK 

GND 

39 

38 

DEVSLP 

PETp1 

37 

36 

UIM-PWR 

PETn1 

35 

34 

UIM-DATA 

GND 

33 

32 

UIM-CLK 

PERp1 

31 

30 

UIM-RESET 

PERn1 

29 

28 

NC 

GND 

27 

26 

NC 

NC 

25 

Summary of Contents for Simatic IPC520A

















































































Reviews: