Siemens Simatic IPC520A Page 23 Operating Instructions Manual Download

Page: 23 / 80

Installing and connecting the device

3.1 Preparing for installation

SIMATIC IPC520A
Operating Instructions, 11/2021, A5E51366325-AA

The following image shows the product label on the SIMATIC IPC520A as an example.

3.1.3

Permitted mounting positions and mounting types

The device can be mounted horizontally on a DIN rail or to a wall.

Horizontal mounting position (preferred)

Desk mounting position

Consider the permitted temperature range for operation that depends on the mounting

position in accordance with the "Technical specifications (Page 47)" section.

Clearances

Ensure that the following clearances measurements to another component or to a wall of a

housing are complied with:
•

Underneath of the device at least 100 mm

•

Side of the device at least 50 mm

Summary of Contents for Simatic IPC520A

















































































Search results

Summary of Contents for Simatic IPC520A

Reviews:

Related manuals for Simatic IPC520A

Brands by name

Popular brands

Siemens Simatic IPC520A, Operating Instructions Manual

Search results

Summary of Contents for Simatic IPC520A

Reviews:

Related manuals for Simatic IPC520A

Brands by name

Popular brands