Siemens SENTRON 7KT PAC1600 Series Manual Download Page 33

Page: 33 / 76

Description

3.4 Parameterization

7KT multimeter
Manual, 08/2018, 2514284149-01

P02.10

Permits the measurement and display of energies according to individual

phases.

P02.11

Permits the measurement and display of voltage and current unbalances.

P02.12

Activates the measurement and display of voltage and current THDs (% har-

monic distortion) and display of the harmonics for current and voltage (2 ... 15).

P02.13

Permits the calculation and display of phase shift.

P02.14

In the event of an alarm, the display backlighting flashes to annunciate the

fault.

M03 Password

Unit

Default

Range

P03.01

Enable password

–

OFF

•

OFF

•

P03.02

User-level password

1000

0 … 9999

P03.03

Administrator password

2000

P03.01

When OFF is set, the password setting is deactivated and access to settings

and the command menu is unrestricted. You can find more information in

chapter Command menu (Page 36).

P03.02

Sets the user password.

P03.03

Sets the password for extended access privileges.

Summary of Contents for SENTRON 7KT PAC1600 Series













































































Search results

Summary of Contents for SENTRON 7KT PAC1600 Series

Reviews:

Siemens SENTRON 7KT PAC1600 Series, Manual, Page: 33 / 76

Search results

Summary of Contents for SENTRON 7KT PAC1600 Series

Reviews: