Siemens SENTRON 7KT PAC1600 Series Manual Download Page 32

Page: 32 / 76

Description

3.4 Parameterization

7KT multimeter

Manual, 08/2018, 2514284149-01

M02 Utility

Unit

Default

Range

P02.01

Language

–

English

•

English

•

Italiano

•

Francais

•

Espanol

•

Portuguese

•

Deutsch

P02.02

High backlight level

100

0 … 100

P02.03

Low backlight level

0 … 50

P02.04

Low backlight delay

5 … 600

P02.05

Default page return

•

OFF

•

10 … 600

P02.06

Default page

–

VL-L

•

VL-L

•

VL-N

•

…

P02.07

Default subpage

INST

•

INST

•

AVG

•

P02.08

Display update time

0.5

0.1 … 5.0

P02.09

Exported energy measure

–

OFF

•

OFF

•

P02.10

Phase energy measure

P02.11

U/I asymmetry measure

P02.12

THD harmonic measure

•

OFF

•

THD

•

THD/HAR

P02.13

Power unbalance measure-

ment

•

OFF

•

P02.14

Backlight flash when in

alarm

P02.05

•

OFF: Display always shows the most recently selected menu page.

•

Value set: The display returns to the page set using P02.06 after this time

has elapsed.

P02.06

Number of the page that is automatically displayed as soon as time P02.05

has elapsed since a key was pressed.

P02.07

Type of page to which the display returns after P02.05 has elapsed.

P02.09

Permits the measurement and display of exported energies.

Summary of Contents for SENTRON 7KT PAC1600 Series













































































Search results

Summary of Contents for SENTRON 7KT PAC1600 Series

Reviews:

Siemens SENTRON 7KT PAC1600 Series, Manual, Page: 32 / 76

Search results

Summary of Contents for SENTRON 7KT PAC1600 Series

Reviews: