manualshive.com logo in svg

Siemens SENTRON 7KT PAC1600 Series, Manual, Page: 11 / 76

Share
Download
Siemens SENTRON 7KT PAC1600 Series Manual Download Page 11

 

7KT multimeter 
Manual, 08/2018, 2514284149-01 

9

 

 

Safety instructions 

2 

2.1

 

Safety instructions 

 

 

 

DANGER 

Risk of death due to electric shock and arc flashover! 
For the 5 A device, it is only possible to measure the current via external current 

transformers. When using the current transformers, the circuit is not protected by a fuse. 

•

 

Switch off and lock out all power supplying this equipment before working on the device. 

•

 

Never open the secondary circuit of the current transformers under load. 

•

 

Short-circuit the secondary current terminals of the current transformer before removing 

this device. 

•

 

Always follow the safety instructions for the current transformers used. 

 

 

DANGER 

Risk of death due to hazardous voltage! 
Before starting work, disconnect the system and the device from the power supply. 

 

 

WARNING 

Possible risk of death due to damaged device! 
Using devices when they are damaged may result in death, serious injury, or property 

damage. 

•

 

Do not install damaged devices. 

•

 

Do not start up damaged devices. 

 

 

NOTICE 
Equipment damage due to lack of fusing 
Non-fused voltage measuring inputs may lead to device and equipment damage. 
Always protect the device with an IEC approved fuse or with an IEC approved miniature 

circuit breaker. 

 

Summary of Contents for SENTRON 7KT PAC1600 Series













































































Reviews:

No comments