Siemens SENTRON 3WA System Manual Download Page 29

Page: 29 / 82

Status of the circuit breaker

3.11 Status of the ETU error messages (self-monitoring function)

3WA Air Circuit Breaker Communication
System Manual, 11/2021, 92310000004-02

3.11

Status of the ETU error messages (self-monitoring function)

The ETU600 electronic trip unit has a self-monitoring and diagnostics function.
The messages of the watchdogs and diagnostics functions can be indicated and evaluated in

the "ETU error messages" register.

Note

Depending on the severity of the error, the circuit breaker may trip. An ETU600 error should

always be checked by your Service personnel.

Bit 1 of register 0x61DA (ETU status) is a type of group signal for register 0x61DE. If an error

message is active, bit 1 of register 0x61DA (ETU status) is also active.

Name

Register (0x0000 HEX)

ETU error messages

0x61DE

Description

Bit

ETU defective (ERROR code 0x00000001)

ETU defective (ERROR code 0x00000002)

ETU defective (ERROR code 0x00000004)

ETU defective (ERROR code 0x00000008)

Option plug defective

ETU defective (ERROR code 0x00000020)

ETU defective (ERROR code 0x00000040)

ETU defective (ERROR code 0x00000080)

ETU defective, rotary switch I

ETU defective, rotary switch t

ETU defective, rotary switch I

ETU defective, rotary switch t

ETU defective, rotary switch I

ETU defective (ERROR code 0x00002000)

ETU defective (ERROR code 0x00004000)

ETU defective (ERROR code 0x00008000)

ETU defective (ERROR code 0x00010000)

ETU defective (ERROR code 0x00020000)

ETU firmware update error

ETU defective (ERROR code 0x00080000)

ETU defective (ERROR code 0x00100000)

VTM defective

ETU defective (ERROR code 0x00400000)

ETU defective (ERROR code 0x00800000)

Current sensor L1 defective

Current sensor L2 defective

Current sensor L3 defective

Current sensor N defective

Summary of Contents for SENTRON 3WA



















































































Search results

Summary of Contents for SENTRON 3WA

Reviews:

Related manuals for SENTRON 3WA

Brands by name

Popular brands

Siemens SENTRON 3WA, System Manual

Search results

Summary of Contents for SENTRON 3WA

Reviews:

Related manuals for SENTRON 3WA

Brands by name

Popular brands