Siemens SENTRON 3WA System Manual Download Page 69

Page: 69 / 82

PROFINET IO

6.4 Interrupt, error and system messages

3WA Air Circuit Breaker Communication
System Manual, 11/2021, 92310000004-02

"BlockType" data block

0x0002: AlarmNotification "Low" for diagnostic alarms
0x0001: AlarmNotification "High" for process alarms

"BlockLength" data block

The number of subsequent bytes of the diagnostic data set is coded in the "BlockLength" data

field. This corresponds to the length of the diagnostic data set without the number of bytes

for the "BlockType" and "BlockLength" data fields, each of which has a length of 2 bytes.

"BlockVersion" data block

W#16#0100: Block version of this diagnostic data set is 1.0.

"AlarmType" data block

W#16#0001: Diagnostic alarm
W#16#0002: Process alarm

"API" data block

API (Application Process Identifier): The COM190 uses the default API "0".

"SlotNumber", "SubslotNumber" data blocks

The COM190 is a modular PROFINET IO device with the following structure:

Designation

SlotNumber

SubslotNumber

COM190

•

Interface

•

Port1

•

Port2

0x0001

0x8000

0x8001

0x8002

3WA

0x0001

"ModuleIdentNumber", "SubmoduleIdentNumber" data blocks

The ModuleIdentNumber and SubmoduleIdentNumber of the module causing the alarm.

"AlarmSpecifier" data block, sequence

Bits

Meaning

Bit 0 … 10

Sequence number

Bit 11

Channel diagnosis available

Bit 12

Manufacturer-specific status information available

Bit 13

At least one channel diagnosis available

Bit 14

Reserved

Bit 15

At least one of the modules configured within this AR signals a

diagnostic event.

Summary of Contents for SENTRON 3WA



















































































Search results

Summary of Contents for SENTRON 3WA

Reviews:

Related manuals for SENTRON 3WA

Brands by name

Popular brands

Siemens SENTRON 3WA, System Manual

Search results

Summary of Contents for SENTRON 3WA

Reviews:

Related manuals for SENTRON 3WA

Brands by name

Popular brands