Siemens SENTRON 3WA System Manual Download

Page: 68 / 82

PROFINET IO

6.4 Interrupt, error and system messages

3WA Air Circuit Breaker Communication

System Manual, 11/2021, 92310000004-02

6.4

Interrupt, error and system messages

6.4.1

General

The COM190 communication module is designed as a diagnostics-capable IO device. It

detects internal and external faults and signals them to the IO controller as diagnostic,

maintenance or process alarms. These can be evaluated, for example, in TIA using the alarm

OBs.
You can obtain detailed information on the error event when an alarm occurs, e.g. using the

SFB54 (RALRM) in the corresponding alarm OB.
The alarms of the COM190 are implemented as diagnostic, maintenance or process alarms

with channel information.

6.4.2

Structure of the diagnostic messages

The basic structure of the diagnostic data sets with the individual data blocks is described

below.

Diagnostic, maintenance and process alarms

The structure of the diagnostic data sets for all alarm messages is identical apart from the

"UserStructIdentifier" field.
The alarm block types start after the "UserStructIdentifier" field. They can occur one to n times

and contain the actual diagnostic, maintenance or process alarm information.

Block structure for alarms

Meaning

Length

BlockType

2 bytes

BlockLength

2 bytes

BlockVersion

2 bytes

AlarmType

2 bytes

API

4 bytes

SlotNumber

2 bytes

SubslotNumber

2 bytes

ModuleIdentNumber

4 bytes

SubmoduleIdentNumber

4 bytes

AlarmSpecifier

2 bytes

Interrupt block type (one to n times)

x bytes

Summary of Contents for SENTRON 3WA



















































































Search results

Summary of Contents for SENTRON 3WA

Reviews:

Related manuals for SENTRON 3WA

Brands by name

Popular brands

Siemens SENTRON 3WA, System Manual

Search results

Summary of Contents for SENTRON 3WA

Reviews:

Related manuals for SENTRON 3WA

Brands by name

Popular brands