Siemens SENTRON 3WA System Manual Download Page 22

Page: 22 / 82

Status of the circuit breaker

3.5 Status of the mechanical system

3WA Air Circuit Breaker Communication

System Manual, 11/2021, 92310000004-02

3.5

Status of the mechanical system

The register "Status of the circuit breaker mechanical system" is used for monitoring the

mechanical system of the circuit breaker.

Name

Register (0x0000 HEX)

Status of mechanical system of circuit breaker

0xCB3B

Description

Bit

Comment

Ready to close

All ready-to-close conditions fulfilled.

Stored energy mechanism charged

Main contacts closed

The main contacts of the circuit breaker

are closed/open.

Connected position

Withdrawable circuit breaker in the guide

frame in the connected position.

Test position

Withdrawable circuit breaker in the guide

frame in the test position.

Second auxiliary release active

The second auxiliary release has been

activated, the main contacts of the circuit

breaker are open.

ETU tripping

Protection tripping has occurred in the

circuit breaker, the main contacts of the

circuit breaker are open.

Stored energy mechanism defective

S40 signaling switch defective

Signaling switch on BSS200 (breaker sta-

tus sensor) module defective.

S41 signaling switch defective

S44 signaling switch defective

S46 signaling switch defective

S47 signaling switch defective

BSS200 error

BSS200 module probably needs to be

replaced, please contact Service.

Circuit breaker overtemperature

Temperature on BSS200 module too high,

function and service life of the module

can be affected.

BSS200 error

BSS200 module probably needs to be

replaced, please contact Service.

Fault in closing coil (CC)

It is probably no longer possible to close

the circuit breaker by means of a commu-

nication command, please contact Ser-

vice.

Fault in opening coil (ST)

It is probably no longer possible to open

the circuit breaker by means of a commu-

nication command, please contact Ser-

vice.

BSS200 error

BSS200 module probably needs to be

replaced, please contact Service.

Summary of Contents for SENTRON 3WA



















































































Search results

Summary of Contents for SENTRON 3WA

Reviews:

Related manuals for SENTRON 3WA

Brands by name

Popular brands

Siemens SENTRON 3WA, System Manual

Search results

Summary of Contents for SENTRON 3WA

Reviews:

Related manuals for SENTRON 3WA

Brands by name

Popular brands