Siemens SD 270 Service Manual Download Page 9 | Manualshive

Page: 9 / 58

Siemens SD 270 Service Manual Download Page 9

SM010-3 Siemens SD 270 Operating & Service Manual Page 9

2.6 Data transfer to a computer

Please refer to Appendix 4 for important information
regarding the connection of non-medical electrical
equipment to medical electrical equipment

The audiometer can be upgraded with an option to allow connection to a
computer with the NOAH application for the transfer of air conduction,
bone conduction, speech and ULL test results (see 3.10). You must use
the designated cable which is supplied with this option.

2.7 Line in/out connection (audio)

Please refer to Appendix 4 for important information
regarding the connection of non-medical electrical
equipment to medical electrical equipment

The Siemens SD 270 has audio line in/out connections for CD or tape
player input (e.g. for recorded speech testing) and amplifier output.

Important Note:

Line out connections are switched on only when FREEFIELD is selected.
The following connections apply to both LINE IN and LINE OUT.

Main Body Segment

Mid segment

End segment

Ground

Right Channel

Left Channel

For more information on live and recorded speech please see Appendix 1.

3 Using the Audiometer

3.1 Ambient conditions

Audiometric testing should always be performed in a quiet room or in an
acoustic booth.

3.2 Switching the audiometer on and off

Press the

key highlighted centre right of the front panel. No warm-up

time is required. The display will briefly show the model and the type of
headphone currently selected for use.

«
...
7
8
9
10
11
...
»

Summary of Contents for SD 270



























































Reviews:

No comments