manualshive.com logo in svg

Siemens SD 270, Service Manual, Page: 8 / 58

Share
Download
Siemens SD 270 Service Manual Download Page 8

 

Page 8 

 

               

 D00073611 Siemens SD 270 Service Manual 

Socket 

Label 

Socket Type 

Colour 

Code 

Connected Part 

Notes 

MIC 1 

3.5mm jack 

 

Speech Input Microphone *  

MONITOR 

3.5mm jack 

 

Monitor Earphone * 

 

BONE 

6.3mm jack 

Grey 

Bone Vibrator Headset * 

 

INSERT 

3.5mm jack 

 

Masking Earphone * 

 

RIGHT 
LEFT 

6.3mm jack 
6.3mm jack 

Red 
Blue 

Air conduction headset * 
 

 

MIC 2 

3.5mm jack 

 

Talkback Microphone * 

 

POWER 

2.5mm power 
jack 

 

Mains AC/DC Adapter * 

 

RESPONSE 

6.3mm 

jack 

Black 

Patient Response Switch * 

 

LINE IN 
LINE OUT 

3.5mm jack 
3.5mm jack 

 

CD/tape player 
External amplifier 

See 
2.7 

DATA 

6 pin mini DIN 

 

Printer * 

See 
2.5 

USB 

USB Connector  

Computer (via USB port) 

See 
2.6 

 
The relevant part numbers are indicated in Section 12. 
 

For connected parts marked * only connect the 
accessories supplied with the instrument or supplied by 
Siemens or a Siemens distributor. These parts have been 
tested for use with the Siemens SD 270 Diagnostic 
Audiometer for compliance with the standards IEC 60601-
1 and IEC 60601-1-2. The use of accessories other than 
those specified may compromise compliance with these 
standards. For other sockets refer to Appendix 4. 

 

2.5 Data transfer to a printer 
 

Please refer to Appendix 4 for important information 
regarding the connection of non-medical electrical 
equipment to medical electrical equipment 

 
 
The audiometer can be upgraded with an option to allow connection to a 
designated portable thermal printer for printing air conduction, bone 
conduction, speech and ULL test results (see 3.9). You must use the 
designated cable which is supplied with this option. 
 
Upon receipt of the printer it must be initially charged for a minimum of 15 
hours prior to use. 
 

 

 

Summary of Contents for SD 270



























































Reviews:

No comments