manualshive.com logo in svg

Siemens SD 270, Service Manual, Page: 14 / 58

Share
Download
Siemens SD 270 Service Manual Download Page 14

 

Page 14 

 

               

 D00073611 Siemens SD 270 Service Manual 

talkback level may be adjusted by the SIGNAL

 

rotary 

control while key is held down. 

 
PRINT 

Press to print audiogram; see Section 3.11 for further 
details 

 
dB STEP 

Enables the operator to set either 2.5dB or 5dB as the 
default step size. 

 
PHONES 

This option is only available if the E-5A insert earphone is 
enabled; this will allow the operator to select the required 
output transducers. 

 
STORE 

Saves the displayed combination of frequency, attenuation 
and ear as a threshold retention value. Please see Section 
3.7 for further details. 

 

 

3.6.4 

TEST MENU 

 

This key enables the selection of the following standard tests. Exit each 
test by pressing the TEST MENU key again. 

 
Menu Option  Description 
 
STENG.   

Stenger: Routes tone or speech to both earphones 

 

simultaneously. Use the SIGNAL rotary control to adjust 
the Left channel level and the MASK rotary control to 
adjust the right. Refer to Appendix 1 for details of the 
Stenger test in speech mode. 

 

ABLB          

Alternate Binaural Loudness Balance: Routes tone to each 
earphone alternately. Use the SIGNAL rotary control to 
adjust the Left channel level and the MASK rotary control 
to adjust the right. Pressing the PRESENT key interrupts 
the signal presented. 

 
SISI 

Short Increment Sensitivity Index: Presents a tone 
continuously at the level and frequency displayed. 
Pressing the PRESENT key increases the level by the 
increment shown on the lower line of the display. Change 
this increment by using the UP & DOWN softkeys. Softkey 
4 switches between the initial display and a counter that 
logs and displays the results of the test as a percentage: 

Summary of Contents for SD 270



























































Reviews:

No comments