Siemens SCALANCE XR524-8C Operating Instructions Manual Download Page 41

Page: 41 / 100

Assembling

4.7 Inserting and removing media pluggable transceivers

SCALANCE XR-500
Operating Instructions, 05/2014, A5E03275845-05

4.7.2

Inserting an SFP / SFP+ transceiver

Follow the steps below to insert an SFP / SFP+ transceiver:
1.

Remove the sealing plug of the SFP / SFP+ slot.

Close the clip of the SFP / SFP+ transceiver.

Insert the SFP / SFP+ transceiver in the SFP / SFP+ slot until you hear it engage.
The SFP / SFP+ transceiver is then firmly secured.

Insert the connecting cable into the SFP / SFP+ transceiver until you hear it engage.
The connecting cable is then firmly secured.

4.7.3

Removing an SFP / SFP+ transceiver

Notes on deinstallation

CAUTION

Risk of burns due to the high temperatures of the pluggable transceiver
The SFP / SFP+ transceivers can be plugged and pulled during operation. Leave the

transceiver to cool down as much as possible.

Procedure

Follow the steps below to remove an SFP / SFP+ transceiver:
1.

Remove the connecting cable of the SFP / SFP+ transceiver.

Open the clip of the SFP / SFP+ transceiver.

Remove the SFP / SFP+ transceiver from SFP / SFP+ slot.

Note
Do not use force
It must be possible to remove the SFP / SFP+ transceiver easily and without applying any

force.

Close the SFP / SFP+ slot with a sealing plug.

Summary of Contents for SCALANCE XR524-8C





































































































Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands

Siemens SCALANCE XR524-8C, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands