Siemens SCALANCE XR524-8C Operating Instructions Manual Download Page 32

Page: 32 / 100

Assembling

4.3 19" rack mounting

SCALANCE XR-500

Operating Instructions, 05/2014, A5E03275845-05

Procedure

Figure 4-1

19" rack mounting of the SCALANCE XR552-12M. SCALANCE XR524-8C/SCALANCE

XR528-6M are mounted in the same way.

To mount the device in a 19" rack, follow the steps below:
1.

Secure the two mounting brackets with four screws each (M3 x 6 supplied with the

product) to the side panels of the device

①

The maximum tightening torque for these screws is 0.5 Nm.
The dimensions of the mounting brackets depend on the height units of the device.

Position the device at the required location and screw the device to the 19" rack

②

Summary of Contents for SCALANCE XR524-8C





































































































Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands

Siemens SCALANCE XR524-8C, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands