Siemens SCALANCE XR524-8C Operating Instructions Manual Download Page 35

Page: 35 / 100

Assembling

4.5 Four-point mounting

SCALANCE XR-500
Operating Instructions, 05/2014, A5E03275845-05

Procedure

Figure 4-2

Attaching the mounting bracket to a SCALANCE XR552-12M. SCALANCE XR524-

8C/SCALANCE XR528-6M are mounted in the same way.

To install the device with a four-point mounting, follow the steps below:
1.

Secure the four mounting brackets each with four countersunk screws (M3 x 6 supplied

with the product) to the side panels of the device

①

The maximum tightening torque for these screws is 0.5 Nm.
The dimensions of the mounting brackets depend on the height units of the device.

Position the device at the required location and screw the device with suitable round-head

screws (6 mm diameter)

②

Summary of Contents for SCALANCE XR524-8C





































































































Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands

Siemens SCALANCE XR524-8C, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands