Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 99

Page: 99 / 100

Index

Approvals, 89
Article number, 17
Autonegotiation, 52
AWG, 54

Cable cross section, 54
CE mark, 89
Clip, 46
Combo port, 17, 21, 22, 23 , 31
Command Line Interface, 63
Command Line Interface (CLI), 69
Components of the product, 19
Configuration, 29
Connection to Industrial Ethernet, 71, 73, 74, 76, 78,
80, 82
Cross section, 54

Dimensions, 71 , 73, 74, 76, 78, 80 , 82

Electrical data, 71, 73 , 74, 76 , 78, 80, 82
Environmental conditions, 71, 73, 74 , 76, 78 , 80, 82

Factory defaults, 29 , 70
Factory setting, 29, 70
Fault LED, 21, 22, 23 , 27
Functional ground, 65

Glossary, 7
Grounding screw, 21, 22, 23 , 66

Housing, 71, 73 , 74, 76, 78, 80, 82

Installation, 71, 73, 74 , 76, 78 , 80, 82
Installation on a DIN rail, 42

LED display

Fault LED, 21, 22 , 23, 27
LED L, 21, 22, 23
Port LED, 21, 22 , 23, 27 , 28
RM LED, 21 , 22, 23 , 27

LED L, 21, 22 , 23

MDI / MDI-X autocrossover, 52
Mounting

Bracket, 21, 22 , 23, 40
Rack, 21, 22, 23 , 40

MTBF, 72, 73, 75, 77, 79, 81 , 83

Overvoltage protection, 56

Permitted ambient conditions, 71, 73, 74, 76, 78, 80,
82
Pin assignment, 51
Pluggable transceiver

Inserting, 46
Notes on deinstallation, 47
Removing, 47

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

Summary of Contents for SCALANCE XR-300WG





































































































Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands

Siemens SCALANCE XR-300WG, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands