Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 71

Page: 71 / 100

Technical specifications

8.1

Technical specifications of the SCALANCE XR324WG

8.1.1

24 VDC variant

The following technical specifications apply to the 24 VDC variant of the SCALANCE XR324WG.

Technical specifications
Connection to Industrial Ethernet
Electrical connectors

Quantity

Connector

RJ45 jack

Properties

Half/full duplex, MDI‑X pinning

Transmission speed

10 / 100 Mbps

Diagnostics interface
Serial interface

Quantity

Connector

RJ-11 jack

Electrical data
Power supply

Design

Terminal block, 2 terminals

Rated voltage

24 VDC

Voltage range

19.2 to 28.8 VDC Safe Extra Low Voltage (SELV)

Cable cross section

≥ 0.75 mm

(20 AWG)

Property

Implemented redundantly

Fusing

5 A / at least 60 V
Or power supply with LPS or NEC class 2

Current consumption

300 mA

Effective power loss

7.2 W

Permitted ambient conditions
Ambient temperature

During operation up to 3000 m above mean
sea level

0 ℃ to +60 ℃

During storage

-40 °C to +85 °C

During transportation

-40 °C to +85 °C

Relative humidity

During operation at 25 ℃

≤ 95% without condensation

Housing, dimensions and weight
Design

Rack

Housing material

Metal

Degree of protection

IP30

Dimensions (W x H x D)

482.6 x 43.6 x 127 mm

Weight

2700 g

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

Summary of Contents for SCALANCE XR-300WG





































































































Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands

Siemens SCALANCE XR-300WG, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands