Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 74

Page: 74 / 100

8.2

Technical specifications of SCALANCE XR326-2C PoE WG

The following technical specifications apply to the SCALANCE XR326-2C PoE WG.

Technical specifications
Connection to Industrial Ethernet
Electrical connectors

Quantity

Connector

RJ45 jack

Properties

Half/full duplex, MDI‑X pinning

Transmission speed

10 / 100 / 1000 Mbps

Combo ports

Quantity

Electrical connec‐
tors

Quantity

Connector

RJ45 jack

Properties

Half/full duplex, MDI‑X pinning

Transmission speed

100 / 1000 / 10000 Mbps

Slots for pluggable
transceivers

Quantity

Connector

SFP transceiver

Transmission speed

1000 / 10000 Mbps

Diagnostics interface
Serial interface

Quantity

Connector

RJ-11 jack

Electrical data
Power supply

Design

Socket, 3 pin

Rated voltage

100 to 240 V AC

Voltage range

85 to 264 VAC

Frequency

50 Hz to 60 Hz

Frequency range

47 Hz to 63 Hz

Properties

Not implemented redundantly

Current consumption

At 100 VAC

Max. 4 A

At 240 V AC

Effective power loss

Max. 280 W
Depending on the effective power loss of the con‐
nected PoE consumers

Permitted ambient conditions
Ambient temperature

During operation up to 3000 m
above mean sea level

During operation in permitted installation positions
0 ℃ to +60 ℃

During storage

-40 °C to +85 °C

During transportation

-40 °C to +85 °C

Relative humidity

During operation at 25 ℃

≤ 95% without condensation

Housing, dimensions and weight
Design

Rack

Housing material

Metal

Degree of protection

IP30

Dimensions (W x H x D)

482.6 x 43.6 x 227.3 mm

Technical specifications
8.2 Technical specifications of SCALANCE XR326-2C PoE WG

SCALANCE XR-300WG

Operating Instructions, 03/2021, C79000-G8976-C454-07

Summary of Contents for SCALANCE XR-300WG





































































































Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands

Siemens SCALANCE XR-300WG, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands