Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 76

Page: 76 / 100

8.3

Technical specifications of the SCALANCE XR328-4C WG

8.3.1

24 VDC variant

The following technical specifications apply to the 24 VDC variant of the SCALANCE XR328-4C
WG.

Technical specifications
Connection to Industrial Ethernet
Electrical connectors

Quantity

Connector

RJ45 jack

Properties

Half/full duplex, MDI‑X pinning

Transmission speed

10 / 100 Mbps

Combo ports

Quantity

Electrical connec‐
tors

Quantity

Connector

RJ45 jack

Properties

Half/full duplex, MDI‑X pinning

Transmission speed

10 / 100 / 1000 Mbps

Slots for pluggable
transceivers

Quantity

Connector

SFP transceiver

Transmission speed

1000 Mbps

Diagnostics interface
Serial interface

Quantity

Connector

RJ-11 jack

Electrical data
Power supply

Design

Terminal block, 2 terminals

Rated voltage

24 VDC

Voltage range

19.2 to 28.8 VDC Safe Extra Low Voltage (SELV)

Cable cross section

≥ 0.75 mm

(20 AWG)

Property

Implemented redundantly

Fusing

5 A / at least 60 V
Or power supply with LPS or NEC class 2

Current consumption

500 mA

Effective power loss

12 W

Permitted ambient conditions
Ambient temperature

During operation up to 3000 m
above mean sea level

0 ℃ to +60 ℃

During storage

-40 °C to +85 °C

During transportation

-40 °C to +85 °C

Relative humidity

During operation at 25 ℃

≤ 95% without condensation

Housing, dimensions and weight
Design

Rack

Technical specifications
8.3 Technical specifications of the SCALANCE XR328-4C WG

SCALANCE XR-300WG

Operating Instructions, 03/2021, C79000-G8976-C454-07

Summary of Contents for SCALANCE XR-300WG





































































































Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands

Siemens SCALANCE XR-300WG, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands