Siemens SCALANCE W720 Configuration Manual Download Page 21

Page: 21 / 432

Description

2.3 The CLI command prompt

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 11/2014, C79000-G8976-C351-03

Global Configuration mode

In this mode, you can make basic configuration settings. In addition to this, you can also call

up modes for the configuration of special interfaces or functions, for example to configure a

VLAN or a PLUG. You change to this mode by entering

configure terminal

in the Privileged

EXEC mode. You exit this mode by entering

end

exit

Other configuration modes

From the Global Configuration mode, you can change to other configuration modes for

special tasks. These are either general configuration modes (for example line configuration,

interface configuration) or protocol-specific configuration modes (FTP, NTP).

2.3

The CLI command prompt

Overview

The Command Line Interface prompt shows the following information:

●

The mode in which the CLI is currently operating.

Most commands can only be called in a particular mode. You should therefore check the

CLI mode based on the command prompt.
–

User Exec mode:

CLI>

–

Privileged Exec mode and configuration modes:

CLI(...)#

●

The selected interface when the CLI is in an Interface Configuration mode.

In the Interface Configuration mode, the parameters are configured for one specific

interface. The command prompt is displayed in the form

CLI(config-if-$$$)#

where the

placeholder

$$$

is replaced by the identifier of the Interface. You select the Interface by

setting suitable parameters for the

interface

command.

●

An identifier when the Trial mode is enabled.

If you first test changes to the configuration and then want to discard them, disable the

Auto save function with the

no auto-save

command. You are then in Trial mode.

Changes to the configuration that you have not saved are indicated by an asterisk in front

of the command prompt:

*CLI(...)#

You save the changes to the configuration with the command

write startup-config

. With

the

auto-save

command, you enable the Auto save function again.

Note
Upper and lower case
The Command Line Interface does not distinguish between upper case and lower case

letters.
Make sure, however, that names used by the operating system or other programs are

correctly written.
Blank
To use blanks in a text, enter the text in quotes, for example "H e l l o"

Summary of Contents for SCALANCE W720

















































































































































































































































































































































































































































Search results

Summary of Contents for SCALANCE W720

Reviews:

Related manuals for SCALANCE W720

Brands by name

Popular brands

Siemens SCALANCE W720, Configuration Manual

Search results

Summary of Contents for SCALANCE W720

Reviews:

Related manuals for SCALANCE W720

Brands by name

Popular brands