Siemens RUGGEDCOM RST2228 Installation Manual Download Page 43

Page: 43 / 50

RUGGEDCOM RST2228

Installation Guide

Chapter 6

Certification

Approvals

Certification

The RUGGEDCOM RST2228 device has been thoroughly tested to guarantee its conformance with recognized

standards and has received approval from recognized regulatory agencies.

NOTE

Certifications related to individual modules are detailed in the RUGGEDCOM Modules Catalog for the

device available online.

CONTENTS

•

Section 6.1, “Approvals”

•

Section 6.2, “EMC and Environmental Type Tests”

Section 6.1

Approvals

The following details the approvals issued for the RUGGEDCOM RST2228.

CONTENTS

•

Section 6.1.1, “CSA”

•

Section 6.1.2, “European Union (EU)”

•

Section 6.1.3, “FCC”

•

Section 6.1.4, “FDA/CDRH”

•

Section 6.1.5, “ISED”

•

Section 6.1.6, “TÜV SÜD”

•

Section 6.1.7, “RoHS”

•

Section 6.1.8, “Other Approvals”

Section 6.1.1

CSA

This device meets the requirements of the following Canadian Standards Association (CSA) standards under

certificate 16.70068356:
•

CAN/CSA-C22.2 No. 60950-1

Information Technology Equipment – Safety – Part 1: General Requirements (Bi-National Standard, with UL

60950-1)

Summary of Contents for RUGGEDCOM RST2228



















































Search results

Summary of Contents for RUGGEDCOM RST2228

Reviews:

Related manuals for RUGGEDCOM RST2228

Brands by name

Popular brands

Siemens RUGGEDCOM RST2228, Installation Manual

Search results

Summary of Contents for RUGGEDCOM RST2228

Reviews:

Related manuals for RUGGEDCOM RST2228

Brands by name

Popular brands