Siemens RUGGEDCOM RST2228 Installation Manual Download Page 4

Page: 4 / 50

Table of Contents

RUGGEDCOM RST2228

Installation Guide

Chapter 4

Communication Ports ......................................................................................

4.1  SFP Transceivers .........................................................................................................................  25
4.2  Available Modules ....................................................................................................................... 27
4.3  Installing/Removing Modules .......................................................................................................  28

Chapter 5

Technical Specifications ..................................................................................

Chapter 6

Certification ....................................................................................................

6.1 Approvals ................................................................................................................................... 37

6.2 EMC and Environmental Type Tests .............................................................................................. 40

Summary of Contents for RUGGEDCOM RST2228



















































Search results

Summary of Contents for RUGGEDCOM RST2228

Reviews:

Related manuals for RUGGEDCOM RST2228

Brands by name

Popular brands

Siemens RUGGEDCOM RST2228, Installation Manual

Search results

Summary of Contents for RUGGEDCOM RST2228

Reviews:

Related manuals for RUGGEDCOM RST2228

Brands by name

Popular brands