Siemens NK8237 MP4.81-01 Installation Manual Download Page 64

Page: 64 / 86

Configuration
Downloading the NK8237

64
Building Technologies

A6V10854379_a_en

CPS Fire Safety

30.11.2017

To enable the secure download or to set the FTP mode, select the related option in

the Node tab of the NK8237 node. If enabled, the secure download makes use of

the TCP port 20500 instead of the ports 20 and 21 required by FTP.

Note: For IT security reasons we recommend always using the secure download

mode.

9.10.1

Verifying the connection to the NK8237 unit

The download requires that the TCP/IP connection between the host PC and the

unit works properly. To check the connection, when required by the download

configuration procedures, proceed as follows:
1. Run the Command Prompt.

From the Start menu:

Start > Programs > Accessories > Command Prompt



The Command Prompt window displays.

2. Type:

ping n.n.n.n

where n.n.n.n is the 4-number IP address of the unit. Then press ENTER.

3. Analyze the reply message.

– If the IP connection is good, the message text will look like the following:

Reply from n.n.n.n: bytes=… time… TTL=…

– If the IP connection is not working for any reason, different messages may

display (Request timed out, Destination net unreachable, and so on). In

these cases, verify the network settings and cabling and try again.

9.10.2

NK8237 configuration download

The NK8237 configuration download procedure includes:



Verifying the connection [➙ 64] to the NK8237 unit.



Downloading the configuration file.

Downloading the configuration file

1. Right-click the NK8237 node.
2. Select Node Commands > Download Configuration File.



The download procedure starts.

Note: In the same menu, you can also create a backup copy of the NK8237

configuration INI file (Create INI file), which might be helpful for troubleshooting.

After the download, the NK8237 unit stops and then reboots. The restart phase is

monitored by the Composer tool.

9.10.3

NK8237 firmware download procedure

The NK8237 firmware download procedure includes:



Configuring the network infrastructure.



Verifying the connection to the NK8237 unit (see Verifying the connection to

the NK8237 unit [➙ 64].)



Downloading the firmware file and (if required) a new configuration file.

Summary of Contents for NK8237 MP4.81-01























































































Search results

Summary of Contents for NK8237 MP4.81-01

Reviews:

Siemens NK8237 MP4.81-01, Installation Manual, Page: 64 / 86

Search results

Summary of Contents for NK8237 MP4.81-01

Reviews: