manualshive.com logo in svg

Siemens NK8237 MP4.81-01, Installation Manual, Page: 30 / 86

Share
Download
Siemens NK8237 MP4.81-01 Installation Manual Download Page 30

5 

Hardware installation 
NE8001 housing solution for NK823x 

 

30 
Building Technologies 

 

A6V10854379_a_en 

CPS Fire Safety 

 

30.11.2017 

 

 

 

WARNING 

Supporting wall must not be composed of inflammable material. 

 

360 mm

415 mm

 

Cabinet installation 

The VAC power supply wires (1.5 mm

2

) should be connected as illustrated in 

Figure 

VAC power connection. 

 

 

 

WARNING 

Careful attention should be paid to the correct connections of VAC power lines. 

 

Ground

Phase

Neutral

Input VAC
1.5 mm

2

 wires

 

VAC power connection 

Wires pass through 20 mm (cut-out) holes at the top of the cabinet (see Figure 

Top 

view of NE8001 cabinet), and continue behind the cabinet to pass through the rear-

side cavity to the entrance hole (see Figure 

Wiring (1) – Front view of cabinet 

(arrow indicates cut-out holes) and Figure Wiring (2) – Entrance hole indicated by 

arrow) where they should be anchored securely before being connected to the 

screw terminators. 

Summary of Contents for NK8237 MP4.81-01























































































Reviews:

No comments