Siemens MK8000 MP4.30 Installation/Configuration Manual Download Page 86

Page: 86 / 92

Tips for Integrating with an OPC client

Building Technologies

048_DMS_MK8000_ICC_MP4.30_A6V10062407_a_en

Fire Safety & Security Products

06.2010

Removing OPC Transparency Support

Once installed, the OPC Transparency values should not be deleted from the reg-
istry by hand. Instead, use the utility provided to remove it.

Please note that OPC Transparency should not be deleted from the PC where the
OPC server resides.

To remove the OPC Transparency registry values, do the following:

Copy the ‘Delete Transparent OPC.reg’ file to the OPC client PC (MK8000 in-
stallation dir>\Utilities\OPC Transparency).

Double-click the file to remove the registry file.

Summary of Contents for MK8000 MP4.30





























































































Search results

Summary of Contents for MK8000 MP4.30

Reviews:

Related manuals for MK8000 MP4.30

Brands by name

Popular brands

Siemens MK8000 MP4.30, Installation/Configuration Manual

Search results

Summary of Contents for MK8000 MP4.30

Reviews:

Related manuals for MK8000 MP4.30

Brands by name

Popular brands