Siemens KMS Assembly And Operating Instructions Manual Download Page 4

Page: 4 / 89

BA 9137 en 12/2015

Foreword

The term "Assembly and operating instructions" will in the following also be shortened to "instructions"
or "manual".

The term

2014/34/EU" used in these instructions applies to the version designed in conformity to

directive 94/9/EC, if the product is put on the market by 19.04.2016, and to the version designed in
conformity to directive 2014/34/EU, if the product is put on the market on or after 20.04.2016.

Symbols in these assembly and operating instructions

This symbol additionally indicates an imminent risk of explosion in the meaning of Directive 2014/34/EU.

This symbol additionally indicates an imminent risk of burns due to hot surfaces in the meaning of
standard "DIN EN ISO 137321".

This symbol warns against risks from lifted and/or suspended loads.

Earthconnection point

Airrelief point

yellow

Oilfilling point

yellow

Oildraining point

white

Oil level

red

Oil level

red

Oil level

red

Connection for
vibrationmonitoring device

Lubricating point

red

Apply grease

Lifting eye

Eye bolt

Do not unscrew

Alignment surface, horizontal

Alignment surface, vertical

These symbols indicate the oillevel checking procedure using the oil dipstick.

These symbols indicate that the oil dipstick must always be firmly screwed in.

Summary of Contents for KMS


























































































Search results

Summary of Contents for KMS

Reviews:

Related manuals for KMS

Brands by name

Popular brands

Siemens KMS, Assembly And Operating Instructions Manual

Search results

Summary of Contents for KMS

Reviews:

Related manuals for KMS

Brands by name

Popular brands