Siemens KMS Assembly And Operating Instructions Manual Download Page 74 | Manualshive

Page: 74 / 89

background image

BA 9137 en 12/2015

10.

Maintenance and repair

Observe the instructions in section 3. "Safety instructions" and in section 9. "Faults, causes and remedy"!

Once the maintenance and repair work is completed, the information in section 7. "Start-up" should be
noted.

10.1

General notes on maintenance

Maintenance comprises all measures for preserving and restoring the target condition and for ascertaining
and assessing the actual condition of the technical means of a system.

In this context maintenance is a comprehensive generic concept which can be subdivided into three areas:

─

Inspection

─

Maintenance (including lubrication)

─

Repair

All maintenance and repair work must be carried out carefully and by qualified personnel only (see section
"Qualified Personnel" on page 3 of these instructions).

WARNING

Serious personal injury can be caused by switched-on machine

Shut down the gear unit and the oil-supply system to perform maintenance and/or repair work or prior
to removing the safeguards. Secure the drive unit against accidental start-up. Attach a notice on the
start switch stating clearly that work is in progress on the gear unit.
Observe the relevant accident prevention regulations applicable at the location of the setup site.

Note

For operation and maintenance, the operating manuals in the order specific annex must be observed.
For technical data and control information, refer to the list of equipment prepared specifically for the
order.

WARNING

Risk of personal injury from energised parts

Removing covers, improper use of the machine, false operation or inadequate maintenance might lead
to death, serious personal injury or property damage.
– Always observe the "five safety rules" when working on the machine.

(see Section 3. "Safety instructions").

– Remove covers only in accordance with the instructions of this operating manual.
– Operate the machine properly.
– Conduct regular and professional maintenance on the machine.

NOTICE

Property damage

Damage to the gear unit possible from non-compliance with the specified periods for maintenance and
repair works is possible.
The operator must observe the deadlines specified and adopt these in its own maintenance plans if
required.

«
...
72
73
74
75
76
...
»

Summary of Contents for KMS


























































































Reviews:

No comments

Related manuals for KMS

Brand: UFO Pages: 16

Brand: Gainsborough Pages: 2

Brand: Gainsborough Pages: 2

Brand: Gait up Pages: 12

Brand: Gait up Pages: 6

Brand: Gaiam Pages: 2

Brand: Garmin Pages: 10

Brand: Naviom Pages: 31

Brand: Launch Pages: 3

Brand: Launch Pages: 43

Brand: Launch Pages: 8

Brand: Launch Pages: 67

Brand: Launch Pages: 55

Brand: LAUNCH TECH Pages: 14

X-431 PROS V4.0

Brand: Launch Pages: 80

Brand: Park House Healthcare Pages: 12

Brand: TC Electronic Pages: 14

Brand: Access Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands