Siemens Hicom 150 E Office User And Installation Manual Download Page 91 | Manualshive

Page: 91 / 130

background image

Installing the Hardware

91

your PC manufacturer. If you do not have a free COM port, you
can configure additional COM ports in your PC (for example,
COM3 and COM4) by installing an additional interface card
(available from your PC dealer).

6.

Connect the free COM port to the port on the back of the op-
tiset E control/data adapter using the serial cable provided.

7.

If applicable, connect the headset to the optiset E control/data
adapter.

8.

Reconnect the subscriber line to the optiset E telephone.

9.

Start your PC and install the Attendant P software (

96).

Installing the Hicom Attendant P via a U

P0/E

PCI Card

with Handset Cradle and Handset

The U

P0/E

PCI card is a state-of-the-art, plug-in PCI card that allows

you to connect a PC to your Hicom 150 E Office system as though
it were a system telephone. This means that you can also perform
all switching functions from the PC.

For installation, the card requires a virtual COM port, an interrupt
(IRQ) and an I/O address. Because the card is a PCI card, the system
automatically assigns it the interrupt and the I/O address.
The virtual COM port is a COM port installed over and above your
existing COM ports by means of the supplied software. This virtual
COM port has no external port. Normally, the software configures
the virtual COM port as COM3 because most PCs are equipped
with two COM ports. However, you can also change it to COM4 if
COM3 is already being used.

«
...
89
90
91
92
93
...
»

Summary of Contents for Hicom 150 E Office



































































































































Reviews:

No comments

Related manuals for Hicom 150 E Office

OFFICESERV 100 Series

Brand: Samsung Pages: 22

Brand: Docomo Pages: 18

Brand: LIKUID Pages: 6

Brand: NTT docomo Pages: 68

ONETOUCH POP 7S P330X

Brand: Alcatel Pages: 32

Brand: Alcatel Pages: 51

Brand: Point Mobile Pages: 8

Brand: Serioux Pages: 24

Brand: Sony Ericsson Pages: 85

Brand: ALIGATOR Pages: 13

Brand: 3Skypephone Pages: 36

Brand: Blaupunkt Pages: 30

Brand: Aastra Pages: 48

Brand: AMGOO Pages: 14

Brand: Avaya Pages: 182

8900 - Curve - GSM

Brand: Blackberry Pages: 48

6151 - Cell Phone 30 MB

Brand: Nokia Pages: 1

6185 - Cell Phone - CDMA

Brand: Nokia Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands