Siemens Hicom 150 E Office User And Installation Manual Download Page 53

Page: 53 / 130

Consultation/Transfer/Conference

Conference

You can add another party to an existing call to form a three-party
conference in which all three parties can speak to one another.

Prerequisite:

You are currently conducting a call and another party

is waiting (for example, on consultation hold).

The symbol command button "Initiating conference"

is replaced

by the symbol command button "Terminate conference"

Terminate conference

Click the Clear button to leave the conference; the other two parties
remain interconnected.

Click the toolbar button for initiating a conference. The message
Conference is displayed in the status box for both parties. The
three-party conference is initiated.

You can bring the conference to an end with the symbol command
button "Terminate conference"; all conference members are then
disconnected.

Summary of Contents for Hicom 150 E Office



































































































































Search results

Summary of Contents for Hicom 150 E Office

Reviews:

Related manuals for Hicom 150 E Office

Brands by name

Popular brands

Siemens Hicom 150 E Office, User And Installation Manual

Search results

Summary of Contents for Hicom 150 E Office

Reviews:

Related manuals for Hicom 150 E Office

Brands by name

Popular brands