Siemens H-compact PLUS Operating Instructions Manual Download Page 35

Page: 35 / 83

WOGeneric TEAAC / 2008
Siemens AG Operating Instructions 1.03 1RQ671...-Z

Start-up

7.1

Checking the insulation resistance

Checking the insulation resistance of the stator winding

The insulation resistance of the stator winding needs to be checked prior to commissioning

and again after any extended periods of storage or periods during which the equipment is

not in operation.

WARNING

Hazardous voltage
During and immediately after measurement of the stator winding insulation resistance,

hazardous voltages can be present at some terminals. Contact with these can result in

death, serious injury or material damage.
Check any power cables connected in order to ensure that the line supply voltage cannot

be fed in. Once you have measured the insulation resistance, discharge the winding by

connecting the ground potential.

Measuring the insulation resistance

● Before you begin measuring the insulation resistance, please read the manual for the

insulation resistance meter you are going to use.

● Disconnect any connected main-circuit cables from the terminals before measuring the

insulation resistance.

● Measure the insulation resistance of the winding to the machine housing when the

winding temperature is between 20 and 30 °C. Other values for the insulation resistance

apply at different temperatures.

● When measuring, wait until the final resistance value is reached. This happens after

approximately 1 minute.

Summary of Contents for H-compact PLUS




















































































Search results

Summary of Contents for H-compact PLUS

Reviews:

Related manuals for H-compact PLUS

Brands by name

Popular brands

Siemens H-compact PLUS, Operating Instructions Manual

Search results

Summary of Contents for H-compact PLUS

Reviews:

Related manuals for H-compact PLUS

Brands by name

Popular brands