Siemens H-compact PLUS Operating Instructions Manual Download Page 54

Page: 54 / 83

Maintenance

9.2 Corrective Maintenance

WOGeneric TEAAC / 2008

Siemens AG Operating Instructions 1.03 1RQ671...-Z

9.2.3

Repairing the air intake cowl

WARNING

Rotating or live parts
Live electrical parts are dangerous. Contact with them can cause death, serious injury or

material damage.
Before carrying out any maintenance work on the fan, disconnect the mains connection,

particularly before opening the terminal box. Make sure that the device cannot be switched

back on.

Dismounting

The fan cowl is made of sheet steel and welded together.
● Before the fan cowl is removed, unscrew the terminal box for the speed sensor

completely so that it is not necessary to undo the connections.

Assembly

● When fitting the fan cowl, make sure that the retaining components are correctly installed.
● Check that there is a uniform gap of at least 2mm between the fan impeller and the air

inlet nozzle.

● Before you bolt on the protective screen when assembling, make sure that the deflecting

baffle with nozzle at the air intake opening is adjusted by means of the clamping pins

provided. The radial gap between the air inlet nozzle and the fan impeller should be at

least 2 mm.

9.2.4

Repairing

the

fan

Plastic radial fan impellers have two integrally molded tongues which engage with the

circumferential groove of the shaft to provide axial fixing.

Dismounting

● Before pulling off the fan, disengage the two tongues hold them provisionally in the raised

position, e.g. by means of inserted shim plates.

● Pull off the fan The fan discs each have two openings for the insertion of a pull-off device,

which should be applied so as to act on the hub. Always use a suitable device for pulling

off and pushing on. Do not use a hammer under any circumstances.

Assembly

● Before pushing the fan onto the shaft, make sure that the two integrally molded tongues

which provide axial location in the annular groove are intact.

● Push the fan onto the shaft.

Summary of Contents for H-compact PLUS




















































































Search results

Summary of Contents for H-compact PLUS

Reviews:

Related manuals for H-compact PLUS

Brands by name

Popular brands

Siemens H-compact PLUS, Operating Instructions Manual

Search results

Summary of Contents for H-compact PLUS

Reviews:

Related manuals for H-compact PLUS

Brands by name

Popular brands